do not scale from this print "a" .025 0.64 ref .025 0.64 + .0492.0030 [1.25.08] (no of pos x .03937 [1.0000]) "a" "a" sel-115-01-xxx-s shown c3 fig. 1 c7 .241 6.12 ref (no of pos x .03937[1.0000]) + .128[3.25] ref .213 5.40 ref (no of pos -1) x .03937[1.0000]) .0030 [.076] (no of pos +1) x .03937 [1.0000] .044 1.12 2 max sway (either direction) 2 max sway (typ) 'b' 'c' c1 01 see note 6 see note 6 sel-1xx-xx-xxx-s-xx no of positions -10, -15, -25 row specification -s: single (use sel-xx-s-xx) plating specification -ftl: flash selective pure tin, matte finish (use c-156-xx-ftl): .000003 min gold in contact area, .000120 min matte tin on tail, with .000050-.000150 nickel underplate over entire contact -ltl: light selective pure tin, matte finish (use c-156-xx-ltl): .000010 min gold in contact area, .000120 min matte tin on tail, with .000050-.000150 nickel underplate over entire contact lead style -01: .0250 [.635] -02: .0500 [1.270] packaging c8 c7 blank: no packaging specified -t: tape & reel (for samtec internal use only) [see note 5] -tr: tape & reel (125 pcs min) [see note 5] .185 ref 4.69 "b" .0040[0.102] 'a' section "a"-"a" c2 sel-xx-s-01 c-156-01-xxx (see note 7) .0040[0.10] "a" "b" "b" sel-115-02-xxx-s shown [different as shown, otherwise same as -01 lead style] c4 fig. 2 section "b"-"b" c5 sel-xx-s-02 c-156-02-xxx c sheet of unless otherwise specified, dimensions are in inches. tolerances are: decimals angles .xx: .01[.3] 2 .xxx: .005[.13] .xxxx: .0020[.051] material: 1mm single element low profile assembly by: sel-1xx-xx-xxx-s-xx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing dean p 2/14/2000 2 1 sheet scale: 4:1 insulator: dupont lcp17235; color: black contact: phos bronze c:\enterprisevault\dwg\misc\mktg\sel-1xx-xx-xxx-s-xx-mkt.slddrw notes: 1. represents a critical dimension. 2. burr allowance: .0015[0.038] max. 3. contact to be flush to .003[0.08] recessed with respect to the body. 4. maximum allowable bow: .0025[0.064]. 5. standard reel has 1000 pcs and 14 empty pockets on trailer and 34 empty pockets on leader. 6. outside tails are weld tabs; they will not carry signal. 7. coplanarity includes body and tails. two points on each plastic end arm to be included in coplanarity measurement. (see sheet 2, fig 3) 8. 1 lb. min retention. 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322 revision j
direction of unreeling pocket not detailed 1 max detail 'a' scale 10 : 1 .000 (see note 3) c6 detail 'b' scale 10 : 1 "c" ref .472 ref 12.00 packaging view (sel-115-02-xxx-s-tr shown) (see note 5) .008 0.19 .016 0.39 .014 0.36 62 .024 0.62 detail 'c' scale 20 : 1 plastic arm inspection points (see note 7) fig. 3 end view for coplanarity inspection sheet of 1mm single element low profile assembly by: sel-1xx-xx-xxx-s-xx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing dean p 2/14/2000 2 2 sheet scale: 1:0.333333 c:\enterprisevault\dwg\misc\mktg\sel-1xx-xx-xxx-s-xx-mkt.slddrw revision j 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322
|
